Audi A3 (8V) – Display of speed limit signs on OBD (Coding)
Purpose: Allows you to display speed limit signs on the OBD. (Sign Assist)
The vehicle must be equipped with the 5Q0 camera . (A3 8V phase 1, the camera is located at the top of the windshield at the rearview mirror, in the shape of a triangle)
Attention!! There are 6 lines of coding to do here.
Proceed:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer then connect the other end to the diagnostic socket of your vehicle.
2 – Switch on the ignition then launch the VCDS program.
Line 1:
3 – Click on ” Select ” then click on ” 5F – Information Electr. “.
4 – Click on ” Security Access – 16 ” then enter the code ” 20103 ” .
5 – Click on ” Adaptation – 10 “.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Vehicle function list BAP-traffic_sign_recognition_0x21 ”
7 – On this same page, there is a second drop-down menu but towards the bottom of the page.
On this last one, choose “ activated ” then validate.
Line 2:
3 – Click on “ Select ” then click on “ 5F – Information Electr. “.
4 – Click on “ Security Access – 16 ” then type the code “ 20103 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Vehicle menu operation-menu_display_road_sign_identification ”
7 – On this same page, there is a second drop-down menu but towards the bottom of the page.
On this last one, choose “ activated ” then validate.
Line 3:
3 – Click on “ Select ” then click on “ 5F – Information Electr. “.
4 – Click on “ Security Access – 16 ” then type the code “ 20103 “.
5 – Click on “ Adaptation – 10 “.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Vehicle menu operation-menu_display_road_sign_identification_over_threshold_high “.
7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On the latter, choose “ activated ” then validate.
Line 4:
3 – Click on “ Select ” then click on “ A5 – Frt Sens. Drv. Assist “.
4 – Click on “ Security Access – 16 ” then type the code “ 20103 ”
5 – Click on “ Coding – 07 ” . Then click on “ Long Coding Assistant ”
6 – Choose the byte “ 1 ”
Then in this drop-down menu of Bit 0-7, select “ 01 Coding_VZE coded ”
Line 5:
3 – Click on “ Select ” then click on “ A5 – Frt Sens. Drv. Assist ”.
4 – Click on “ Security Access – 16 ” then type the code “ 20103 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Display end of speed limit symbol ”
7 – On this same page there is a second drop-down menu but towards the bottom of the page.
On the latter, choose “ activated ” then validate.
Line 6:
3 – Click on “ Select ” then click on “ 17 – Instruments ”.
4 – Click on “ Security Access – 16 ” then type the code “ 20103 ”
5 – Click on “ Coding – 07 ” then click on “ Long Coding Wizard ”
6 – Choose the byte “ 5 ”
Then check the Bit “ 2 ”: “ Traffic Sign Recognition installed «
