Audi A1 (GB) – Door lock/unlock confirmation (Beep/Horn) (Coding)
Purpose: Allows you to configure the door locking confirmation with Beep (alarm) or Horn.
Warning!! There are 5 coding lines to do here, see 6. (After coding, activate the option on your screen if it does not work, in CAR – Opening/closing settings – check Acoustic Confirmation)
Proceed:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer then connect the other end to the diagnostic socket of your vehicle.
2 – Switch on the ignition then launch the VCDS program.
Line 1:
3 – Click on “ Select ” then click on “ 09- Central electrics ”.
4 – Click on “ Security Access – 16 ” then enter the code “ 31347 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Acknowledgement signals-Akustische Rueckmeldung entriegeln ”
7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this last one, choose “ Yes ” then validate.
Line 2:
3 – Click on “ Select ” then click on “ 09- Power plant ”.
4 – Click on “ Security Access – 16 ” then type the code “ 31347 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Acknowledgement signals-Akustische Rueckmeldung verriegeln ”
7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this last one, choose “ Yes ” then validate.
Line 3:
3 – Click on “ Select ” then click on “ 09- Power plant ”.
4 – Click on “ Security Access – 16 ” and then type the code “ 31347 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Acknowledgement signals-Akustische Rueckmeldung global ”
7– On this same page there is a second drop-down menu but towards the bottom
of the page.
On this last one, choose “ active ” then validate.
Line 4:
3 – Click on “ Select ” then click on “ 09- Power plant ”.
4 – Click on “ Security Access – 16 ” then type the code “ 31347 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Acknowledgement signals-Menuesteuerung Akustische Rueckmeldung ”
7 – On this same page there is a second drop-down menu but towards the bottom
of the page.
On this last one, choose “ active ” then validate.
Line 5:
3 – Click on “ Select ” then click on “ 09- Power plant ”.
4 – Click on “ Security Access – 16 ” then type the code “ 31347 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Acknowledgement signals-Dauer der Akustischen Rueckmeldung vom Einfachhorn ”
7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On the latter, choose “ normal ” or “ kurz ” (for a short signal) then validate.
!!! If your vehicle is not equipped with the alarm, here is the coding to modify to activate the horn :
Line 6:
3 – Click on “ Select ” then click on “ 09- Centrale électrique ”.
4 – Click on “ Security Access – 16 ” then type the code “ 31347 ”
5 – Click on “ Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Acknowledgement signals-Akustische Rueckmeldung Signalhorn ”
7 – On this same page there is a second drop-down menu but towards the bottom
of the page.
On the latter, choose “ active ” then validate.